A new garage door Installation may enhance the curb appeal and modernize the outside of your house, raise your return on investment, improve the overall safety of your property, and improve your daily convenience. You can get full-service garage door installation from most garage door retailers, including taking down and disposing of your old door, delivering your new door, and installing it. If you have the skill and experience for the job, you can save money on garage door installation costs by doing it yourself.
Installing a Garage Door: How to do this
You must have the right tools and follow the manufacturer’s installation instructions to ensure your new garage door is safe. As you are ready to install your garage door, you should have the following tools and equipment on hand:
- Glasses that are level safe
- Phillips driver bit
- Pliers with adjustable locks
- Socket bit
- Drill
- Drill Bits
- Open-ended wrench
- Hammer
- 1/2-inch rods
Make sure you have the right tools, and then follow these 10 simple steps to install your new sectional garage door.
Let go of the tension in your garage door
For this first step, you’ll want to be very careful because your garage door springs are under much weight and tension. When they aren’t used properly. They can hurt people and damage things. Work on the garage door Installation before you do anything with the torsion spring. Use your adjustable-locking pliers to clamp the shaft of the torsion spring. Then, put your pliers against the header wall above the garage door and hold them there until the torsion spring is free.
When you look at the spring winding cone, you’ll see four holes. These holes loosen and tighten the spring. Putting a steel rod in one of the holes. As you hold the rod in your hand, loosen the screws that hold the winding cone in place. Take each spring apart one-quarter at a time, then switch the two rods. Use one rod to keep the cone steady and the other rod to move the cone around.
Remove the Door from the Garage Door Opener
Once you’ve let go of the tension in the garage door, you can disconnect your garage door from the opener and move on. There is a red emergency release handle that you can use to disconnect the door from the wall safely. When you do this, the trolley arm will be able to move vertically, allowing you to raise or lower the door by hand.
At this point, you can start to remove the sections of the doors:
- Remove the hinges that connect the top panel of the garage door to the panel.
- Remove the bolts from the door frame to disconnect the panel from the track.
- Continue eliminating the hinges from every panel and loosening the hardware on the rest of the sectional panels as you move on.
Garage Door Installation Panels in Sections
Putting up your new garage door installation can now be done for good. To keep your two-car garage door from bowing in the middle, put a reinforcing bar on the top of the door as soon as you get to the panel, drill pilot holes if they haven’t already been done. Then, screw the bar to the panel with screws. For a good installation and assembly, start by:
Assembling each garage door panel with hinges at the top of each one
- Assembling the axle supports to the bottom and top parts of the car
- Placing the bottom panel into the hole and making sure it’s level.
- Install each new panel on top of the last one, making sure that the groove of the upper panel fits on the ridge of the panel below it. Repeat this step until all panels are in the right place, then finish the job.
Secure the hinges and put the tracks
Please make sure the top half of each hinge is attached to the panel on top of it, then put the wheeled axles into the side hinges. Then, put the top and bottom axle supports in place for each. Next, install the track and make sure the wheels are in the right place on the track to make sure it works properly. Finally, join the door cable to the catch on the panel axle support on the bottom. Then, attach the bottom bracket to the wall, and the door will open and close.
Glue the Spring Assemblies to the Track
At this point, put together all the parts that support the spring and connect to the track. Then, with the help of the previous door’s ceiling supports, rest the curved part of the track on the vertical piece you made earlier.
Glue the Tracks together
While garage door installation connects your horizontal and vertical tracks. Then, connect all of your tracks.
Install the Springs
When connecting the spring anchors to the springs, attach the spring locking cone, and fasten the two springs to the header bracket. Make sure they’re tight.
Install the Torsion Rod and the Pulleys
Slide the torsion rod into the holes on the side header brackets to put in the torsion rod. Then, join pulleys to every end of the rod, and you’re done.
Attach a cable
Garage Door Installation from the ground, attach the cable to the pulley wheel and turn the wheel, so any slack is pulled tight over the pulley as you move it around the wheel. Slide the wheel into the header bracket and make sure everything is tight. It’s now time to attach a pair of locking pliers to a rod outside the bracket. This will stop the rod from moving when you tighten the garage door springs.
Tighten the Springs
Your manufacturer’s manual can help you figure out how many turns the springs need to be tightened. Use your steel rods to stiffen the springs. To keep the spring in place, tighten all bolts and remove the pliers from the torsion rod at the right stress level. If you want the company to install your garage door, you don’t need to buy one from them.
Customers should buy their garage doors from big-box stores where they can get their doors quickly because of the long lead times in the garage door business. It doesn’t matter where you buy your garage door from. Cornwell Door Service will still be able to install the door for you. As soon as you hire us to install your garage door, you can ensure it’s done right!
